Thermaltake Pacific W1 CPU Water Block
Thermaltake’s new Pacific W1 CPU Water Block delivers extreme cooling
performance and compatibility for custom PC builders. Featuring 0.15mm internal fin construction, the Pacific
W1 is manufactured with a full copper base and anti-corrosive nickel plating. A universal mounting mechanism
offer error-free as well as no-tools installation, providing the ultimate in cooling performance.
![](pub/media/wysiwyg/key3/db/products/lcs/PacificW1/main.jpg)
Tt LCS Certified
Tt LCS Certified is a Thermaltake exclusive certification applied only to products that pass the design and hardcore enthusiasts standards that a true LCS chassis should hold to. The Tt LCS certification was created so that we at Thermaltake can indicate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations, ensuring you get the best performance from the best features and fitment.
![](pub/media/wysiwyg/key3/db/products/lcs/pic1.jpg)
Anti-corrosion Design
Made in Taiwan, the Pacific W1 Water Block’s specially machined copper base
with nickel coating prevents corrosion and fully complies with Thermaltake’s highest quality standards. The
mating surface to the CPU sports an absolute mirror polish. In combination, these features provide exceptional
heat transfer and anti-corrosion protection for the most demanding use conditions.
![](pub/media/wysiwyg/key3/db/products/lcs/PacificW1/pic2.jpg)
Optimized Micro-channel Structure
The Pacific W1 Water Block is designed with a compact form factor featuring
0.15mm micro-channel fin construction for optimal clearance and extreme heat dissipation. A silicone rod
guides coolant through the bottom of each micro-channel.
![](pub/media/wysiwyg/key3/db/products/lcs/PacificW1/pic3.jpg)
No-Fuss Expansion
Designed to fit all modern CPU sockets with universal mounting mechanisms,
the Pacific W1 allows enthusiasts to build superior water cooling systems from an aesthetic standpoint as well
as incorporate modular chassis upgrades for the future.
![](pub/media/wysiwyg/key3/db/products/lcs/PacificW1/pic3c.jpg)
![](pub/media/wysiwyg/key3/db/products/lcs/PacificW1/pic3d.jpg)
![](pub/media/wysiwyg/key3/db/products/lcs/PacificW1/pic4.jpg)
Cautions
Thermaltake recommends the following steps to be taken
before using
the
Pacific series radiators and water blocks
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop
setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
- Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
- Coolant might fade over time.
P/N | CL-W022-CU00BL-A |
---|---|
Dimensions |
60 H * 54 W* 16 L mm |
중량 |
345 g |
Compatibility |
Intel LGA 2066/2011/1366/1200/1156/1155/1151/1150/775 AMD AM4/FM2/FM1/AM3+/ AM3/AM2+/AM2 |
Threads |
G ¼” |
Heatsink Material |
Copper |