Thermaltake C1000 Opaque Coolant Blue
The latest C1000 Opaque Coolant launched by Thermaltake is used as anti-corrosion protection fluid and heat-transfer medium for PC water-cooling. Made in Germany, the C1000 Opaque coolant is virtually odorless, non-flammable, and high performance liquid, offering superb protection for copper, nickel, brass, and aluminum. Choose from seven vivid colors: red, green, blue, orange, yellow, white, and purple to brighten up any build with Thermaltake.
Tt LCS Certified
Tt LCS Certified is a Thermaltake exclusive certification applied only to products that pass the design and hardcore enthusiasts standards that a true LCS chassis should hold to. The Tt LCS certification was created so that we at Thermaltake can indicate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations, ensuring you get the best performance from the best features and fitment.
German-Made Anti-Corrosive Solution
Being non-flammable, the C1000 Opaque Coolant is a ready-to-use cooling solution with at least 3 years shelf life in airtight containers, providing great performance while preventing the entire cooling system – copper, brass, nickel, and aluminum – from corrosion.
Download MSDS
*MSDS: Material Safety Data Sheet
Biodegradable Material
The C1000 Opaque Coolant is classified in water hazard class 1 (low-rate endangering) according to German water hazard regulations. The product is readily biodegradable.
Vivid Application
Thermaltake C1000 Opaque Coolant is designed specifically for PC liquid cooling systems. Featuring anti-freezing, anti-rusting, water scale prevention and easy application, the C1000 non-transparent coolant brings vivid colors into your build and delivers great thermal efficiency and further reduce the temperature of the system.
Note:
1.The coolant color may change over time.
2.The precipitations at the bottom of the bottle are considered normal.
Cautions
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
Cautions
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks:
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000, which offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse, and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop setup:
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000, which offers great performance while preventing corrosion in the entire cooling system (copper, brass, nickel, aluminum, and steel).
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushes the coolant into the loop.
- DO NOT let the pump run dry. If no liquid is entering the pump, turn off your power immediately.
- Fill the reservoir to the top to prevent air from entering the pump.
- If necessary, tilt the system slightly from side to side to bleed the air out of the loop.
- Place paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
- Before starting, flush out your system properly to prevent any coolant or unwanted particles from sticking to your tubes, radiators, and other cooling components.
- Coolant might fade over time.
| P/N | CL-W114-OS00BU-A |
|---|---|
| 색상 |
Blue，Red，White，Green，Orange，Yellow，Purple，Black |
| Capacity |
1000 ml |
| Hazardous component |
Ethanediol Value < 20% CAS 170-21-1 EG 203-473-3 Index 603-027-00-1 Certificate Xn R-Phrase 22 S-Phrase 2, 24/25,46 |
User Manual
- File Name
- 상세 설명
- Size
- Version
- Release Date
-
Manual
- Multi-language
- 573.2 KB
- 2015-12-23
