Thermaltake Flexible Tubing V-Tubler 3T 3/8’’ (9.5 mm)
Thermaltake introduces the V-Tubler 3T water tubing for custom PC water cooling
configurations. Manufactured from medical grade PVC material, the V-Tubler resists twisting
and collapse allowing for tighter bends without the kinking that can cause cooling failures
or a reduction in system performance. Designed for use with 3/8” barbs and compression
fittings, give users better mounting, easier fitting, and ideal flow. Choose from: ID 1/2”
or 3/8” to make your system a showcase for all to see with the Thermaltake V-Tubler water
tubing.
Tt LCS Certified
Tt LCS Certified is a Thermaltake exclusive certification
applied only to products that pass the design and hardcore enthusiasts standards that a true
LCS chassis should hold to. The Tt LCS certification was created so that we at Thermaltake
can indicate to all power users which chassis have been tested to be best compatible with
extreme liquid cooling configurations, ensuring you get the best performance from the best
features and fitment.
Medical Grade Construction
Made in Taiwan, the V-Tubler 3T is constructed from medical
grade PVC which is reliable, non-toxic, and substance free. Smooth inner walls improve
closed loop sanitation, reducing particular gathering/entrapment onto the tubing wall.
Working temperature range from -4℉ (-20℃) to 140℉ (60℃).
- Inner diameter: 3/8” (9.5 mm)
- Outer diameter: 5/8” (16 mm)
Material of V -Tubler 3T as below:
Remarkable Expansion
Designed for use with 3/8” barbs and compression fittings,
V-Tubler 3T is pre cut into retail coils of 200cm lengths, allowing enthusiasts to build up
aesthetically-superior water cooling systems by allocating the radiators to each particular
component and incorporating externally-modular upgrades for their chassis.
Cautions
Thermaltake recommends the following steps to be taken
before using the Pacific series radiators and water blocks
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop
setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
Cautions
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks:
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000, which offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse, and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop setup:
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000, which offers great performance while preventing corrosion in the entire cooling system (copper, brass, nickel, aluminum, and steel).
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushes the coolant into the loop.
- DO NOT let the pump run dry. If no liquid is entering the pump, turn off your power immediately.
- Fill the reservoir to the top to prevent air from entering the pump.
- If necessary, tilt the system slightly from side to side to bleed the air out of the loop.
- Place paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
- Before starting, flush out your system properly to prevent any coolant or unwanted particles from sticking to your tubes, radiators, and other cooling components.
- Coolant might fade over time.
| P/N | CL-W018-OS00TR-A |
|---|---|
| 색상 | Transparent |
| Inside Diameter |
3/8”(9.5 mm) |
| Outside Diameter |
5/8”(16 mm) |
| Length |
200 cm |
| 재질 | PVC |
